GB744 Info:
- Max Type thru 1/4"
The GB744 is a pneumatic-hydraulic installation tool designed specifically for the efficient installation of 1/4" CHERRYMAX® & AllMax® fasteners, as well as blind rivets. It weighs just over 7 lbs. (3.2 kg) and can be operated in any position. It has a .580" (14.73 mm) fastener setting stroke and a rated pull load of 3,800 lbs. (16.9 kN) on 90 psi (6.2 bar) air pressure at the air inlet.
The GB744 installation tool operates on 90 to 100 psi (6.2 - 6.9 bar) of air pressure, with 90 psi. (6.2 bar) air pressure providing the maximum efficiency. At 90 psi. (6.2 bar) air pressure, the GB744 does not exceed 81.5 dB(A) and consumes .30 SCF/cycle (8.50 L/cycle). The air inlet is provided with 1/4 - 18 female pipe thread for accepting the user's air hose fitting.
Weight | 7 lbs. (3.2 kg) |
Rated Pull Load | 3,800 lbs. (16.9 kN) |
Stroke | .580" (14.73 mm) |
Width | 6.60 (167.6 mm) |
Noise Level | 81.5 dB(A) |
Warranty | 1 year |
Nose Assembly Selection Chart - GB744
CHERRYMAX®
ALLMAX®
HUCKMAX®
HUCK-CLINCH®
MIL-R-7885
NAS9301-9312
BACR15FRFR
BACR15GJ/GK
DIA. | STRAIGHT | RIGHT ANGLE (3) | OFFSET |
---|---|---|---|
1/8 | 456MAX-701-17 1,2 | 456MAX-704-54RA 1,2 | 456MAX-704-43OS 1,2 |
5/32 | 456MAX-744-20 1 | 456MAX-744-50OS 1 | |
3/16 | 456MAX-749-35 1,2,3 | ||
1/4 | 08MAX-744-20 | 08MAX-744A-50OS |
BLIND BOLT (SINGLE ACTION)
WITH OR W/OUT DRIVE
WASHER
MS90353S & U / MS90354S & U
MS21140S & U / MS21141S & U
MAXI-BOLT®,
BACB30YY, YU, & YT
DIA. | STRAIGHT | RIGHT ANGLE (3) | OFFSET |
---|---|---|---|
5/32 | SB05-704A-54RA 2,6 SB05-744-58RA 7 |
||
3/16 | SB06-704-54RA 2,5,6 SB06-744-58RA 7 |
BLIND BOLT (SINGLE ACTION)
WITH DRIVE WASHER
MS90353S & U / MS90354S & U
MS21140S & U / MS21141S & U
MAXI-BOLT®,
BACB30YY, YU, & YT
DIA. | STRAIGHT | RIGHT ANGLE (3) | OFFSET |
---|---|---|---|
5/32 | UBB05-704A-54RA 2,6 UBB05-744-58RA 7 |
||
3/16 | UBB06-704-54RA 2,5,6 UBB06-744-58RA 7 |
FOOTNOTES
GAGE BILT CERTIFIES THE GB744 WILL INSTALL THE ABOVE FASTENERS | |
1) INSTALLS 1/8", 5/32" AND 3/16" DIAMETERS | |
2) NOSE ASSEMBLIES REQUIRE THE 744704 ADAPTER | |
3) FRONT END EJECTING NOSE ASSEMBLY. | |
4) RIGHT ANGLE NOSE ASSEMBLY MAY REQUIRE MORE THAN 1 PULL | |
5) FOR MAINTENANCE ONLY | |
6) NOSE ASSEMBLIES REQUIRE THE 744156 STROKE LIMITER | |
7) HEAVY DUTY |
CREDITS
CHERRYMAX® IS A REGISTERED TRADEMARK OF CHERRY AEROSPACE. HUCKMAX® AND HUCK-CLINCH® ARE REGISTERED TRADEMARKS OF HOWMET AEROSPACE. ALLMAX® IS A REGISTERED TRADEMARK OF ALLFAST FASTENING SYSTEMS, INC. |